Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Last revisionBoth sides next revision
ks:4124 [2018/04/26 02:46] mcmasterks:4124 [2018/04/30 04:53] mcmaster
Line 50: Line 50:
         1 mil wire => 30-30 mils below capillary         1 mil wire => 30-30 mils below capillary
         Greater gap => smaller wire         Greater gap => smaller wire
 +        To adjust: loosen knurled knob
     EFO horizontal     EFO horizontal
         4 mm to left of capillary tip         4 mm to left of capillary tip
         Loosen solenoid clamping screw         Loosen solenoid clamping screw
 +        SHCS allen key: 77 mil
     EFO overtravel     EFO overtravel
         50-60 mil beyond capillary tip         50-60 mil beyond capillary tip
         Loosen solenoid ring set screws         Loosen solenoid ring set screws
 +        SS allen key: 34 mil
 +Capillary adjustment
 +    SHCS allen key: ? couldn't get one to fit. Using pliers to tighten...
 +        diameter: 1.47 mm
 +        thread: 1.25 / 4 = 0.3125 mm
 +    Capillary diameter: 1/16"
 +    Allen key inserted for alignment: 56 mil
 +        63 mil diagonol vs 1/16" => 63 mil
 Wire loading Wire loading
     6.1.10     6.1.10
     First o-ring 3/8" from flared side of funnel     First o-ring 3/8" from flared side of funnel
 </code> </code>
 +
 +150C workholder
  
 ====== Connectors ====== ====== Connectors ======
Line 69: Line 81:
 Suspect has serial port somewhere on it  Suspect has serial port somewhere on it 
  
-^ #   ^ Color  ^ Function  ^ Note                                                                                                                          +^ #  ^ Color  ^ Function  ^ Note                                                                                                                                         
-| 1   |        |           | 9.3.5\\ Set MOTOR switch ON and check for less than 6 Vdc                                                                     | +| 1  |        |           | 9.3.5\\ Set MOTOR switch ON and check for less than 6 Vdc\\ DMM: -150 mV                                                                     | 
-| 2   |        |                                                                                                                                         +| 2  |        |           DMM: 0.65V                                                                                                                                   
-| 3   |        |                                                                                                                                         +| 3  |        |           DMM: -85mV                                                                                                                                   
-| 4   |        |           | 9.27.5 in Manual Z does not function properly\\ 6.1.18.5 in 6.1.18 Z-LVDT ADJUSTMENT\\ +7.6 V Z up ("reset")\\ –8.5 V Z down  | +| 4  |        |           | 9.27.5 in Manual Z does not function properly\\ 6.1.18.5 in 6.1.18 Z-LVDT ADJUSTMENT\\ +7.6 V Z up ("reset")\\ –8.5 V Z down\\ DMM: -230 mV  | 
-| 5   |        |           | 9.3.4\\ With MOTOR switch OFF, rotate cam until LED 1 (RESET) lights up on logic\\ board. Check for 7 Vdc                     +| 5  |        |           | 9.3.4\\ With MOTOR switch OFF, rotate cam until LED 1 (RESET) lights up on logic\\ board. Check for 7 Vdc\\ DMM: 5V                          
-| 6   |        |           | 9.3.2\\ 18 V ptp, 2.5 kHz sine wave                                                                                           +| 6  |        |           | 9.3.2\\ 18 V ptp, 2.5 kHz sine wave\\ DMM: -15V                                                                                              
-| 7   |        |                                                                                                                                         +| 7  |        |           DMM: 0V                                                                                                                                      
-| 8   |        |                                                                                                                                         | +| 8  |        |           DMM 15V                                                                                                                                      |
-| 9          |                                                                                                                                         | +
-| 10  |        |                                                                                                                                         | +
-| 11  |        |                                                                                                                                         | +
-| 12  |        |                                                                                                                                         | +
-| 13  |        |                                                                                                                                         | +
-| 14         |                                                                                                                                         |+
  
 ====== PCB ====== ====== PCB ======
Line 91: Line 97:
 Manual: parts table lists as 4124-4100-0 Logic Board Ass’y, image layout shows the same thing Manual: parts table lists as 4124-4100-0 Logic Board Ass’y, image layout shows the same thing
  
 +Unit: 04125-4210-000-01
  
 ====== mcmaster eBay ====== ====== mcmaster eBay ======
 
 
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution 4.0 International
Recent changes RSS feed Donate Powered by PHP Valid XHTML 1.0 Valid CSS Driven by DokuWiki