This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
| ks:4124 [2018/04/26 02:38] – [Table] mcmaster | ks:4124 [2018/04/30 04:53] – mcmaster | ||
|---|---|---|---|
| Line 25: | Line 25: | ||
| - | ====== | + | ====== |
| < | < | ||
| Line 50: | Line 50: | ||
| 1 mil wire => 30-30 mils below capillary | 1 mil wire => 30-30 mils below capillary | ||
| Greater gap => smaller wire | Greater gap => smaller wire | ||
| + | To adjust: loosen knurled knob | ||
| EFO horizontal | EFO horizontal | ||
| 4 mm to left of capillary tip | 4 mm to left of capillary tip | ||
| Loosen solenoid clamping screw | Loosen solenoid clamping screw | ||
| + | SHCS allen key: 77 mil | ||
| EFO overtravel | EFO overtravel | ||
| 50-60 mil beyond capillary tip | 50-60 mil beyond capillary tip | ||
| Loosen solenoid ring set screws | Loosen solenoid ring set screws | ||
| + | SS allen key: 34 mil | ||
| + | Capillary adjustment | ||
| + | SHCS allen key: ? couldn' | ||
| + | diameter: 1.47 mm | ||
| + | thread: 1.25 / 4 = 0.3125 mm | ||
| + | Capillary diameter: 1/16" | ||
| + | Allen key inserted for alignment: 56 mil | ||
| + | 63 mil diagonol vs 1/16" => 63 mil | ||
| Wire loading | Wire loading | ||
| 6.1.10 | 6.1.10 | ||
| First o-ring 3/8" from flared side of funnel | First o-ring 3/8" from flared side of funnel | ||
| </ | </ | ||
| + | |||
| + | 150C workholder | ||
| ====== Connectors ====== | ====== Connectors ====== | ||
| - | P14 | + | ===== P14 ===== |
| + | |||
| + | Label: TEST | ||
| + | |||
| + | Suspect has serial port somewhere on it | ||
| + | |||
| + | ^ # ^ Color ^ Function | ||
| + | | 1 | | | 9.3.5\\ Set MOTOR switch ON and check for less than 6 Vdc\\ DMM: -150 mV | | ||
| + | | 2 | | | DMM: 0.65V | | ||
| + | | 3 | | | DMM: -85mV | | ||
| + | | 4 | | | 9.27.5 in Manual Z does not function properly\\ 6.1.18.5 in 6.1.18 Z-LVDT ADJUSTMENT\\ +7.6 V Z up (" | ||
| + | | 5 | | | 9.3.4\\ With MOTOR switch OFF, rotate cam until LED 1 (RESET) lights up on logic\\ board. Check for 7 Vdc\\ DMM: 5V | | ||
| + | | 6 | | | 9.3.2\\ 18 V ptp, 2.5 kHz sine wave\\ DMM: -15V | | ||
| + | | 7 | | | DMM: 0V | | ||
| + | | 8 | | | DMM 15V | | ||
| + | |||
| + | ====== PCB ====== | ||
| + | |||
| + | The PCB in the schematic does not match my unit | ||
| - | ^ # ^ Color ^ Function | + | Manual: parts table lists as 4124-4100-0 Logic Board Ass’y, image layout shows the same thing |
| - | | 1 | + | |
| - | | 2 | + | |
| - | | 3 | + | |
| - | | 4 | + | |
| - | | 5 | + | |
| - | | 6 | + | |
| - | | 7 | + | |
| - | | 8 | + | |
| - | | 9 | + | |
| - | | 10 | | | + | |
| - | | 11 | | | + | |
| - | | 12 | | | + | |
| - | | 13 | | | + | |
| - | | 14 | | | + | |
| + | Unit: 04125-4210-000-01 | ||
| ====== mcmaster eBay ====== | ====== mcmaster eBay ====== | ||