This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
ks:4124 [2018/04/02 05:37] – mcmaster | ks:4124 [2018/04/30 04:53] – mcmaster | ||
---|---|---|---|
Line 25: | Line 25: | ||
+ | ====== Calibration ====== | ||
+ | |||
+ | < | ||
+ | 4124 adjustments | ||
+ | Clamp solenoid | ||
+ | Section 6.1.5 | ||
+ | Reccomended: | ||
+ | 5 - 7 mil acceptable for 1-3 mil wire | ||
+ | Must be changed when loading different size wire | ||
+ | Use force gauge (scale?) | ||
+ | Adjust force with nut on right | ||
+ | Adjust distance with set screws on left | ||
+ | Bond force | ||
+ | Section 6.1.6 | ||
+ | Use force gauge (scale) | ||
+ | Search height | ||
+ | Section 6.1.8 | ||
+ | Set to 5 mil | ||
+ | Adjust search dial while chessman held down | ||
+ | EFO electrode adjustment | ||
+ | Section 6.1.11 | ||
+ | Figure 3-8 on page 20 has items labeled | ||
+ | EFO vertical | ||
+ | 1 mil wire => 30-30 mils below capillary | ||
+ | Greater gap => smaller wire | ||
+ | To adjust: loosen knurled knob | ||
+ | EFO horizontal | ||
+ | 4 mm to left of capillary tip | ||
+ | Loosen solenoid clamping screw | ||
+ | SHCS allen key: 77 mil | ||
+ | EFO overtravel | ||
+ | 50-60 mil beyond capillary tip | ||
+ | Loosen solenoid ring set screws | ||
+ | SS allen key: 34 mil | ||
+ | Capillary adjustment | ||
+ | SHCS allen key: ? couldn' | ||
+ | diameter: 1.47 mm | ||
+ | thread: 1.25 / 4 = 0.3125 mm | ||
+ | Capillary diameter: 1/16" | ||
+ | Allen key inserted for alignment: 56 mil | ||
+ | 63 mil diagonol vs 1/16" => 63 mil | ||
+ | Wire loading | ||
+ | 6.1.10 | ||
+ | First o-ring 3/8" from flared side of funnel | ||
+ | </ | ||
+ | |||
+ | 150C workholder | ||
+ | |||
+ | ====== Connectors ====== | ||
+ | |||
+ | ===== P14 ===== | ||
+ | |||
+ | Label: TEST | ||
+ | |||
+ | Suspect has serial port somewhere on it | ||
+ | |||
+ | ^ # ^ Color ^ Function | ||
+ | | 1 | | | 9.3.5\\ Set MOTOR switch ON and check for less than 6 Vdc\\ DMM: -150 mV | | ||
+ | | 2 | | | DMM: 0.65V | | ||
+ | | 3 | | | DMM: -85mV | | ||
+ | | 4 | | | 9.27.5 in Manual Z does not function properly\\ 6.1.18.5 in 6.1.18 Z-LVDT ADJUSTMENT\\ +7.6 V Z up (" | ||
+ | | 5 | | | 9.3.4\\ With MOTOR switch OFF, rotate cam until LED 1 (RESET) lights up on logic\\ board. Check for 7 Vdc\\ DMM: 5V | | ||
+ | | 6 | | | 9.3.2\\ 18 V ptp, 2.5 kHz sine wave\\ DMM: -15V | | ||
+ | | 7 | | | DMM: 0V | | ||
+ | | 8 | | | DMM 15V | | ||
+ | |||
+ | ====== PCB ====== | ||
+ | |||
+ | The PCB in the schematic does not match my unit | ||
+ | |||
+ | Manual: parts table lists as 4124-4100-0 Logic Board Ass’y, image layout shows the same thing | ||
+ | |||
+ | Unit: 04125-4210-000-01 | ||
====== mcmaster eBay ====== | ====== mcmaster eBay ====== |