Differences

This shows you the differences between two versions of the page.

--- mcmaster:uv2000cnc [2015/11/26 19:36] – mcmaster
+++ mcmaster:uv2000cnc [2018/12/26 14:31] (current) – removed mcmaster
@@ Line 1: / Line 1: @@
-Sherline 2000 CNC info
-====== Spindle CNC ======
--11-26 project
-Problem: I got this system 8 or so years ago to learn machining and build robots.  At the time I was learning plenty with manual milling and didn't really step up to do real CNC machining until much later.  That's when I realized:
-    * Didn't come with spindle CNC instructions (encoder, driving)
-    * This is not a Sherline option
-      * Although the encoder does look like the [[http://www.sherline.com/8100pg.htm|Sherline one]]
-    * The company that did it went out of bussiness
-I could try poking around CNCZone and such (probably still should) its probably simple enough that some reasonably quick tinkering will get it working.  I tried guessing settings in the Axis GUI before without success.
-===== Overview =====
-Standard Sherline driver box has a mini-DIN connector on the side labeled "Spindle".  This goes to the spindle controller that has a matching plug as well as an RJ-11 for a tachometer.  The spindle controller also has a switch for "manual" or "CNC".  When flipped to CNC the spindle stops.
-===== Internals =====
-The driver box has a 26 pin header (J6) that is presumably for accessories.  An IDC cable runs to an IDC to mini-DIN converter board is mounted to the top of the driver box.  It has a few capacitors (PWM smoothing?) but is otherwise blank.  There are unused pads for some ICs and other components.  I suspect the mini-DIN is essentially directly connected to the DB-25.
-==== Driver ====
-{{mcmaster:sherline:8760tms:ext.jpg?300}}
-{{mcmaster:sherline:8760tms:ext_mini-din.jpg?300}}
-{{mcmaster:sherline:8760tms:int_j6.jpg?300}}
-{{mcmaster:sherline:8760tms:int.jpg?300}}
-{{mcmaster:sherline:8760tms:int_melted_wire.jpg?300}}
-{{mcmaster:sherline:8760tms:int_mini-din.jpg?300}}
-==== Spindle ====
-{{mcmaster:sherline:6513tms:ext_front.jpg?300}}
-{{mcmaster:sherline:6513tms:ext_top.jpg?300}}
-{{mcmaster:sherline:6513tms:ext_tach.jpg?300}}
-===== Sherline standard pinout =====
-[[http://www.sherline.com/8760pg.htm|8760 driver box]]
-^Pin ^Name ^I/O ^Description ^  \\ Notes \\  \\   \\  |
-|1 |  |I |Input from EMC (may be ignored in other systems)</font>  |  |
-|2 |  |I |X Direction |  |
-|3 |  |I |X Step |  |
-|4 |  |I |Y Direction |  |
-|5 |  |I |Y Step |  |
-|6 |  |I |Z Direction |  |
-|7 |  |I |Z Step |  |
-|8 |  |I |A Direction |  |
-|9 |  |I |A Step |  |
-|10 |  |  |N/C |  |
-|11 |  |O |Output to EMC (may be ignored in other systems)</font>  |  |
-|12 |  |O |Output to EMC, XYZ home (may be ignored in other systems)</font>  |  |
-|13 |  |  |N/C |  |
-|14 |  |I |Input from EMC, C1 (may be ignored in other systems)</font>  |  |
-|15 |  |  |N/C |  |
-|16 |  |I |Input from EMC, C2 (may be ignored in other systems)</font>  |  |
-|17 |  |  |N/C |  |
-|18-25 |  |  |Ground |  |
-===== My pinout =====
-\\